OWNER’S MANUAL
ARP- 1003E
PORTABLE AIR CONDITIONER
ACONDICIONADOR DE AIRE PORTÁTIL
Read and retain these instructions for future reference
For any Customer Support needs please
choose the Customer Support tab on
Royal Centurian Inc.
ARP-1003E
WARNING
Improper handling can cause serious damage to the appliance. Read this manual carefully before operating the unit.
Do not wet the
housing or control
panel.
Do not cover the
air outlet while in
use.
Do not allow
children to play
with the controls or
drop any objects
into the outlet.
Do not place
Always turn the
unit off and remove
the power plug
from the socket
when cleaning.
Do not attempt to
remove any part of
the casing unless
by an authorized
technician.
objects or let any
person sit on top of
the unit.
Remove the plug
from the socket if
the unit is not
being used for long
period.
Use only the
correct power
supply AC
Do not operate the
unit with damaged
plug or loose
115V/60Hz.
socket point.
Make sure that the back of the unit is at least 4" or more from a wall. Do not place the unit in front of curtains or drapes.
WARNING
-If the power cord on this unit is damaged, it must be replaced by the manufacturer service agent or qualified electrician.
-This appliance is not intended for use by children or other persons without assistance or supervision.
3
DESCRIPTION OF COMPONENTS
1
6
7
4
2
3
9
10
8
5
1. Control panel
2. Air outlet (Up-Down and Left-Right)
3. Front panel
6. Screen filter
7. Air intake (Evaporator)
8. Air intake (Condenser)
9. Air outlet (Heat exchange)
10.Water drain with plug
4. Handle
5. Casters
4
ARP-1003E
INSTALLATION INSTRUCTIONS
Connect exhaust hose assembly to the back of the unit. Extend hose to desired length and locate the exhaust nozzle through a window or
wall for ventilation.
EXHAUST ASSEMBLY AND INSTALLATION
Exhaust nozzle connection
Window spacer
Exhaust nozzle Exhaust nozzle connector Exhaust hose Exhaust hose connector
Insert exhaust nozzle from rear.
Attach screws from front.
1. Insert ends of exhaust hose into exhaust nozzle connector and exhaust hose connector by twisting clockwise
until it stops.
2. Attach the exhaust hose connector onto the rear outlet of the unit and turn to the right.
3. Attach the exhaust nozzle to the window spacer with the 4 screws provided.
4. Connect the exhaust nozzle connector to the exhaust nozzle.
5. Extend the exhaust hose and close the window as far as possible trapping the exhaust nozzle as shown below .
INDOOR
INDOOR
INDOOR
5
OPERATION
Control panel
Display
Timer On / Off
Warning Light
Power Control
Timer / Temp
Set Control
Mode Control
Fan Speed Control
POWER CONTROL
The power control turns the unit on and off.
WARNING CONTROL
Condensed water may accumulate in the unit . If the internal tank becomes full, the Warning Light will shine and the unit will not operate until
the unit has been drained.
FAN MODE
When fan mode is selected the indicator light will shine green. Air is circulated throughout the room with no cooling.
NOTE: Unit does not need to be vented in fan mode.
MODE CONTROL
The Mode Control has three settings:
Cool
The settings are adjusted with the Mode Control button. A light will indicate which setting is currently being used.
Dehumidify
Fan
FAN SPEED CONTROL
The Fan Speed Control has 3 settings: High, Medium, and Low.
6
ARP- 1003E
DEHUMIDIFY MODE
When dehumidify mode is selected, the indicator light will shine green. Air is dehumidified as it passes through the unit, without being in full
Cooling mode.The fan will operate in Medium speed. Fan speed is not adjustable in Dehumidify mode.
NOTE: The air exchange hoses must vent inside the room when using Dehumidify mode.
COOL MODE
When Cool mode is selected, the indicator light will shine green. During the Cool mode the air is cooled and hot air is exhausted to the
outside through the exhaust tube.
NOTE: The air exchange hoses must vent outside the room when using Cool mode.
TIMER / TEMP SET CONTROLS
Used for adjusting the timer and thermostat.
The default display is the room temperature.
In Cool mode, when "+" or "-"button is pressed, the set temperature is displayed and may be adjusted. After 15 seconds the display will
revert back to room temperature . Temperature is only adustable in Cool mode . The time is adjustable between 1~12 hours.
NOTE: By pressing both Timer /Temp set buttons at the same time, the display will toggle between Celsius and Fahrenheit.
TIMER
Auto turn off:
With machine in Fan mode, press timer button to select number of hours you would like the unit to run in Cool mode until it
automatically shuts off.
Auto turn on:
With machine powered off, press timer button to select number of hours until you would like the unit to automatically start running in Cool
mode.
After switching the air conditioner off, you must wait 3 minutes before switching it back on again.
7
|